All Items are
American
Made
Fiberglass
Components. Manufactured
and shipped F.O.B. Hampton Florida 32044
80-86 Front
End
87-91 Front End
Call
1-352-468-2203 - We have an extra 87-91 tilt.
$450. Cash & Carry! Save $1399.
Front End
Features:
- Heavy Duty version - comes complete with hinge kit
- Grey exterior gellcoat finish can be easily sanded and
prepared for finishing.
- Order Anytime, Click listing at top of page. - Smooth 90° roll into wheel well openings, generally
extends in a full
¾". - The units do come with mold flashing - which must be
fared in before
preparing for paint.
- Pre-Split Front End models come with the lower
fender section (the part between the
door and tire) separate. It is manufactured with a tongue & groove
joint on both
the panel and the front end, to
help in closing
alignment.
- One Piece Front Endsdo need the rear fender panel to be cut in order to
utilize the hinge kit supplied.....They can be made to slide forward than tilt without
cutting the fender, however, this
depends on the tire size and will involve detailed planning and
fabrication on the installers part.
- The interior finish is Fiberglass texture - coated in black lacquer - it comes
without wheel wells.
Wheel wells cannot be completely attached to the front end as they will
interfere with engine &
firewall component, when hinging.
This 92-96 Front End will
actually fit 80-96 Ford Trucks and has become most popular
"Doghouse" for Mud Boggers / Pull Trucks & Drag Racers alike.
Simply add aftermarket lens covers to finish out!
Remember to order
your race parts, by phone, this month and take an extra 20% off the
above pricing.
92-96 Front End
-
Light Weight Version - is
intended for racing applications and does not come with a hinge
kit.
- Order Anytime, Click listing at top of page.
- These unit generally only weigh in at approx 30# +/- .
- Pre-Split models are not available in Light Weight.
NOTE: When ordering Light Weight version truck racing components are
"Special Order" and Non
Returnable.
IMPORTANT - Please specify the type of racing that the unit will be used for, so we
may build and reinforce your unit accordingly. Units manufactured for "Mud Bog"
racing have a heavier roving on all edges to reduce the chance of tearing (under to stress
of impact and mud load) and usually weigh
10 - 15# more than a Drag Racing unit. Units manufactured for "Sand Drag"
or "Baja" style racing are built so as to be midway between the Street Drag and
the Mud Bog units.
80-86
3" Dominator™ Hood
Heavy Duty Features:
larger pic
- Fully Lined TECHHOOD™
design Bolts Directly to the
OEM hinge & Latch.
- Order Anytime, Click listing at top.
- Hi-Rise design provides an
additional 3" clearance.
80-86
Dominator™ Inner View - Rear Baffle must be
cut open
to provide a functional cold air.
- 90° edges come long - may
need sanded for a correct fit.
87-91
3" Dominator™ Hood
Heavy Duty Features:
larger pic
- Fully Lined TECHHOOD™
design Bolts Directly to the
OEM hinge & Latch.
- Order Anytime, Click listing at top.
- Hi-Rise design provides an
additional 3" clearance.
87-91 Dominator™ Inner View - Rear Baffle must be
cut open to
provide a functional cold air.
- 90° edges come long - may
need sanded for a correct fit.
92-96
3" Dominator™ Hood
Heavy Duty Features:
larger pic
- Fully Lined TECHHOOD™
design Bolts Directly to the
OEM hinge & Latch.
- Order Anytime, Click listing at top.
- Hi-Rise design provides an
additional 3" clearance. Installed Photos
92-96
Dominator™ Inner View - Rear Baffle must be
cut open to
provide a functional cold air.
- 90° edges come long - may
need sanded for a correct fit.
80-86
GT-500 Hood Heavy Duty Features:
larger pic
- Fully Lined TECHHOOD™
design Bolts Directly to the
OEM hinge & Latch.
- GT-500 design provides an
additional 2" clearance.
- Rear Baffle & Front Scoops
must be cut open to be made
functional.
- To Order, Click
listing at top.
- 90° edges come long - may
need sanded for a correct fit. Installed Photos
80-86
GT-500 Inner View
- Rear Baffle must be
cut open
to provide a functional cold air.
- 90° edges come long - may
need sanded for a correct fit.
87-91
GT-500 Hood Heavy Duty Features:
larger pic
- Fully Lined TECHHOOD™
design Bolts Directly to the
OEM hinge & Latch.
- GT-500 design provides an
additional 2" clearance.
- Rear Baffle & Front Scoops
must be cut open to be made
functional.
- To Order, Click listing at
top.
- 90° edges come long - may
need sanded for a correct fit. Installed Photos
87-91
GT-500 Inner View
- Rear Baffle must be
cut open
to provide a functional cold air.
- 90° edges come long - may
need sanded for a correct fit.
92-96
GT-500 Hood Heavy Duty Features:
larger pic
- Fully Lined TECHHOOD™
design Bolts Directly to the
OEM hinge & Latch.
- GT-500 design provides an
additional 2" clearance.
- Rear Baffle & Front Scoops
must be cut open to be made
functional.
- To Order, Click listing at
top.
- 90° edges come long - may
need sanded for a correct fit. Installed Photos
92-96
GT-500 Inner View
- Rear Baffle must be
cut open
to provide a functional cold air.
- 90° edges come long - may
need sanded for a correct fit.
