All Items are
American
Made
Fiberglass
Components. Manufactured
and shipped F.O.B. Hampton Florida 32044
73-87 Cabs Short Wheel
Base 117.5" - Long Wheel Base 131.5" - Blazer W.B. 106.5" Features: - One Piece Outer shell construction - with a few well hidden mold seams.
- Smooth, easy to prep and paint, gray sandable exterior gellcoat finish.
- Aluminum plate reinforced firewall & door hinge areas provides the necessary
strength for
proper support of factory doors & hardware.
- Marine Grade Pressure treated floor support beams are sealed into the fiberglass
and covered
with black lacquer finish.
- The unit arrives bare
without dash, doors or any mechanical or electrical devices.
- Headliner is supplied and comes with a smooth paintable gellcoat interior
finish.
(Comes separately and requires professional installation.)
- Light Weight Model comes with out floor and firewall - This unit is solely
intended for serious
racing applications. Tube chassis and metal interior work is required.
(Approx. weight 50 -
70#)
- Drag-Package
Includes: Race Weight Cab, Front End, Doors & Bedsides or Stepside
fenders. Please e-mail or call us after placing your order. Reference
your order number and specify your choice of hood and bedside or fender
choice by part number. You MUST specify your type of racing so the parts
can be made accordingly. Race weight parts only.
Note:
Factory installed floor braces may need to
be trimmed or removed for desired fit.
Cabs - although strong, straight, rust free &
reliable - are not the project for the average "Joe". They are intended
for the serious "Ground Up Builder" who has the time, money & experience to
do the job correctly.
All safety concerns must be taken up with the
chassis shop involved with the project.
Once finished these cabs look exceptional and should just about last forever,
however, sit down and Please give some serious thought before ordering........We prefer
that our customers be confident & educated in the amount of work required to complete
this project and secure in the choice that you make. Please Note:
We are unable to ship cab shells. They must be picked up in person to
avoid freight damage.
Installed Photos All parts shown above were
used on our 73-80 Chevy Build-Up
73-80 Stock Hood
Heavy Duty Features:
- Smooth grey gellcoat finish.
- Frame uses existing hinge &
latch. Additional hold downs
recommended.
- Fiberglass texture inner coated
with Black Lacquer.
- Smooth grey gellcoat outer
finish.
- Add a new scoop for as little as $50 w / purchase.
73-80 Stepdown Hood
Heavy Duty Features:
- Smooth grey gellcoat finish.
- Frame uses existing Hinge
only (Discard Latch)
- Fiberglass texture inner coated
with Black Lacquer.
- Smooth Grey gellcoat outer
finish.
73-80
Cowl Induction Hood
Heavy Duty Features:
- Styled after the Z-28 design.
- 90 edges on both sides help to
maintain fender contours.
- Fully Lined TECHHOOD™ design
- Utilizes OEM hinge & latch.
-
Additional hold downs recommended.
- Smooth Gellcoated. paintable inner
finish. Scoop & baffle come closed.
- Full Open inner chamber provides 2."
of additional clearance.
- Coremat® reinforced skin.
73-80 Super Sport
Hood
Heavy Duty Features:
- Styled after the 2000 Z-28 design.
- 90 edges on both sides help to
maintain fender contours.
- Fully Lined TECHHOOD™ design
- Utilizes OEM hinge & latch.
- Additional hold
downs recommended.
- Smooth Gellcoated. paintable inner
finish. Scoop & baffle come closed.
- Full Open inner chamber provides 3."
of additional clearance.
- Coremat® reinforced skin.
73-80 Cowl
Induction Hood
Heavy Duty Features:
- Styled after the original Z-28 design.
- 90 edges on both sides help to
maintain fender contours.
- Fully Lined TECHHOOD™ design
- Utilizes OEM hinge & latch.
- Additional hold
downs recommended.
- Smooth Gellcoated. paintable inner
finish. Scoop & baffle come closed.
- Full Open inner chamber provides3.5"
of additional clearance.
- Coremat® reinforced skin.
81-87 Stock
Hood Heavy Duty Features:
- Smooth grey gellcoat finish.
- Frame uses existing Hinge &
Latch.
- Additional hold downs recommended.
- Fiberglass texture inner coated
with Black Lacquer.
- Smooth Grey gellcoat outer
finish.
- Add a new scoop for as little as $50 w / purchase.
81-87
Stepdown Hood Heavy Duty Features:
- Smooth grey gellcoat finish.
- Frame uses existing Hinge
only (Discard Latch)
- Fiberglass texture inner coated
with Black Lacquer.
- Smooth Grey gellcoat outer
finish. Installed Photos
81-87 Indy
Cowl Hood 2" Heavy Duty Features:
- Indy design provides 2" extra
clearance - Air box comes
closed.
- Fully Lined
TECHHOOD™
-
Additional hold downs recommended.
- Smooth Grey gellcoat outer
finish. Installed Photos
81-87 Cowl
Induction Hood
Heavy Duty Features:
- Styled after the original Z-28 design.
- 90 edges on both sides help to
maintain fender contours.
- Fully Lined TECHHOOD™ design
- Utilizes OEM hinge & latch.
- Additional hold downs recommended.
- Smooth Gellcoated. paintable inner
finish. Scoop & baffle come closed.
- Full Open inner chamber provides3.5"
of additional clearance.
- Coremat® reinforced skin.
81-87 Super Sport
Hood
Heavy Duty Features:
- Styled after the 2000 Z-28 design.
- 90 edges on both sides help to
maintain fender contours.
- Fully Lined TECHHOOD™ design
- Utilizes OEM hinge & latch.
- Additional hold downs recommended.
- Smooth Gellcoated. paintable inner
finish. Scoop & baffle come closed.
- Full Open inner chamber provides 2."
of additional clearance.
- Coremat® reinforced skin.
81-87 Ram Air II
Hood
Heavy Duty Features:
- Styled after the 2000 T/A design.
- 90 edges on both sides help to
maintain fender contours.
- Fully Lined TECHHOOD™ design
- Utilizes OEM hinge & latch.
- Additional hold downs recommended.
- Smooth Gellcoated. paintable inner
finish. Scoop & baffle come closed.
- Full Open inner chamber provides3."
of additional clearance.
- Coremat® reinforced skin.
(All
Units are Interchangeable between the years - Chevy or GMC)
73-87 Front End
Features:
- Heavy Duty version - comes complete with hinge kit
- Grey exterior gellcoat finish can be easily sanded and
prepared for finishing.
- Smooth 90° roll into wheel well openings, generally
extends in a full
¾".
- The units do come with mold flashing - which must be
fared in before
preparing for paint.
- Pre-Split Front End models come with the lower
fender section (the part between the
door and tire) separate. It is manufactured with a tongue & groove
joint on both
the panel and the front end, to
help in closing
alignment.
-
One Piece Front Endsdo need the rear fender panel to be cut in order to
utilize the hinge kit supplied.....They can be made to slide forward than tilt without
cutting the fender, however, this
depends on the tire size and will involve detailed planning and
fabrication on the installers part.
- The interior finish is Fiberglass texture - coated in black lacquer - it comes
without wheel wells.
Wheel wells cannot be completely attached to the front end as they will
interfere with engine &
firewall component, when hinging.
-
Light Weight Version -
is intended for racing applications and does not come with a hinge
kit.
- These unit generally only weigh in at approx 30# +/- .
- Pre-Split models are not available in Light Weight.
NOTE: Light Weight version truck racing components are
"Special Order" and Non
Returnable.
IMPORTANT - Please specify the type of racing that the unit will be used for, so we
may build and reinforce your unit accordingly. Units manufactured for "Mud Bog"
racing have a heavier roving on all edges to reduce the chance of tearing (under to stress
of impact and mud load) and usually weigh 10 - 15# more than a Drag Racing unit. Units manufactured for "Sand Drag"
or "Baja" style racing are built so as to be midway between the Street Drag and
the Mud Bog units.
73-87
Wheel Well
Heavy Duty Features:
- Smooth grey gellcoat finish.
- One Piece fiberglass
construction.
- Battery Acid resistant
Gellcoat.
- All Holes are closed and
require drilling for installation.
73-91
Blazer Frt. Flr. Pan
Heavy Duty Features:
- Smooth grey gellcoat finish.
- One Piece fiberglass
construction.
- Rivets in place.
- Designed to cover floor board
rot.
73-80 Dash repro
Heavy Duty Features:
- Smooth grey gellcoat finish
- One Piece fiberglass
construction 73-87 Front Bumper
- All Holes are closed and
require drilling for installation.
73-87 Door - Hinge Type
Installed Photos
Heavy Duty Features:
- Smooth grey gellcoat finish both inside and out.
- Accepts original hinge, latch & regulator hardware
- Double wall posts support upper window and track.
- Windows come blanked in and must be opened during installation
- Coremat® reinforced outer skin reduces "print thru".
- Original felts can be epoxied in the door post and side track.
- Door is supplied bare with no glass, mechanism, tracks or hardware.
73-87
Fleetside Bedside
Heavy Duty Features:
- Smooth grey gellcoat exterior finish - Fiberglass textured Black
Lacquer inner.
- Skin Only - Will not bolt to stock location. Installed Photos
73-87 Stepside Fender
w/step
Heavy Duty Features:
- Smooth gray gellcoat exterior
finish - Fiberglass textured
Black Lacquer inner.
- Smooth 90° roll into wheel well
- Rear flange holes come closed
and require back drilling for
correct alignment.
Installed Photos
73-87 Stepside Bed (Short Wheel Base Box -
117.5" w.b.)
Heavy Duty Features:
- Bed Comes complete with fenders & steps attached - as one piece. Ideal
for customized or
frenched in taillight applications.
- Double panel side walls, with a smooth gray gellcoat inner and outer finish.
- Hollow sealed stake pocket - can be opened if desired for original appearance.
- Design for use and abuse with heavy Marine Grade PT under floor
reinforcements - which can
support the same weight load as the original bed.
- Gellcoated Fiberglass floors - recessed 3/4" to allow for the installation of
"Aftermarket" Bed Wood
Kits.
- Black lacquer over fiberglass texture underneath the bed floor and on the forward
side of the back
splash.
- Tubbed
bed allows for 21" clearance from tub to wheel opening flange. This allows for
20"-21" tires.
The distance between the tubs is 33".
- Side flange is angled and does not have the curled design of the original
bed (Due to compound
curve & fiberglass mold limitations.)
- Installation time (after removal of original box ) 1-2 hours.
Note:
Factory installed floor braces may need
to be trimmed or removed for desired fit.
To install - simply drill thru the bed and the under floor reinforcements and thru
bolt it in place with O.D washers. It may be necessary to drill a new mounting hole
through the existing frame. Drilling - sanding and possible notching of under floor
braces may be required for correct installation of your NEW and
IMPROVED, RUST FREE, DENT
FREE bed assembly. (Ground wire required for electrical)
73-87 Fleetside Bed (Long Wheel Base Box -
131.5" - Short Wheel Base ) Heavy Duty Features:
- Bed Comes complete with bedsides attached - as one piece. Ideal for
customized or
frenched in taillight applications.
- Box section side walls, with a smooth grey gellcoat inner and outer finish.
- Hollow sealed stake pocket - can be opened if desired for original appearance.
- Design for use and abuse with heavy Marine Grade PT under floor
reinforcements - which can
support the same weight load as the original bed.
- Gellcoated Fiberglass floors have a ribbed design - eliminated the need for a Wood
kit.
- Black lacquer over fiberglass texture underneath the bed floor and on the forward
side of the back
splash.
-
Installation time (after removal of original box ) 1-2 hours.
Note:
Factory installed floor braces may need
to be trimmed or removed for desired fit.
To install - simply drill thru the bed and the under floor
reinforcements and thru bolt it in place with O.D washers. It
may be necessary to drill a new mounting hole through the existing
frame. Drilling - sanding and possible notching of under floor
braces may be required for correct installation of your NEW
and
IMPROVED, RUST FREE,
DENT FREE bed assembly. (Ground wire required for
electrical) Please Note:
We are unable to ship 8' Beds. They must be picked up in person to
avoid freight damage.
Phone
Mon- Thurs 9am-2pm est (352) 468-2203
FAX Orders can be sent 24/7 at
(352) 468-2164
