68-69 Stock Hood
Heavy Duty Features:
- 90 edges on both sides help to maintain fender
contours.
- Full perimeter inner frames - utilizes OEM hinge
(Original striker plate must be installed from the
metal hood for use with latch.)
- Black lacquered fiberglass textured inner.
- Sandable gray gellcoated exterior finish.
- Coremat® reinforced skin aids in
reduction of
print-thru.
Add a new scoop for as little as $50 w / purchase. |
68-69 Stage
1 Hood
Heavy Duty Features:
- Styled after the original design.
- 90 edges on both sides help to maintain fender
contours.
- Full perimeter inner frames - utilizes
OEM hinge
(Original striker plate must be installed from the
metal hood for use with latch.)
- Black lacquered fiberglass textured inner.
- Sandable gray gellcoated exterior finish.
- Coremat® reinforced skin. |
|
70-72 Stock Hood
- Small Lip
Heavy Duty Features:
- 90 edges on both sides help to maintain fender
contours.
- Full perimeter inner frames - utilizes OEM hinge
(Original striker plate must be installed from the
metal hood for use with latch.)
- Black lacquered fiberglass textured inner.
- Sandable gray gellcoated exterior finish.
- Coremat® reinforced skin aids in
reduction of
print-thru.
Add a new scoop for as little as $50 w / purchase.
|
70-72 Stock Hood - Big Lip
Heavy Duty Features:
- 90 edges on both sides help to maintain fender
contours.
- Full perimeter inner frames - utilizes OEM hinge
(Original striker plate must be installed from the
metal hood for use with latch.)
- Black lacquered fiberglass textured inner.
- Sandable gray gellcoated exterior finish.
- Coremat® reinforced skin aids in
reduction of
print-thru.
Add a new scoop for as little as $50 w / purchase. |
70-72 G.S. Hood
Heavy Duty Features:
- Styled after the original design.
- 90 edges on both sides help to maintain fender
contours.
- Full perimeter inner frames - utilizes
OEM hinge
(Original striker plate must be installed from the
metal hood for use with latch.)
- Black lacquered fiberglass textured inner.
- Sandable gray gellcoated exterior finish.
- Coremat® reinforced skin.
|
70-72 Cowl
Induction 3.5" Hood
Heavy Duty Features:
- Styled after the original Z-28 design.
- 90 edges on both sides help to maintain fender
contours.
- Full perimeter inner frames - utilizes
OEM hinge
(Original striker plate must be installed from the
metal hood for use with latch.)
- Black lacquered fiberglass textured inner.
- Sandable gray gellcoated exterior finish.
- Coremat® reinforced skin.
You
can add a ram air isolator plate during check out. |
70-72 Front Fender
Race Weight Features:
- Smooth gray gellcoat exterior finish..
- Fiberglass texture, Black lacquer inner finish.
- Hood Jam holes,
hinging and attaching points
must be opened for installation.
- Mold flashing must be removed for finishing.
- No other reproduction fiberglass fenders come
so complete.
- Partial inner jam provides attach points only.
- Not designed for hinge type hood.
- Fiberglass race weight pin-on hood required.
- Inner jam may vary from
photo.
|
70-72 Trunk Lid
Race Weight Features:
- Full perimeter bracing.
- 90 edges on both sides help to maintain body
contours.
- Black lacquered fiberglass textured inner.
- Sandable gray gellcoated exterior finish.
- Reinforced skin aids in reduction of print-thru.
Heavy Duty Features:
- Utilizes stock hinge & latch. Lower spring
tension required.
|
 |
70 Bumper
Race Weight Features:
- Black lacquered fiberglass textured inner.
- Sandable gray gellcoated exterior finish.
- Reinforced skin aids in reduction of print-thru. |
|
