All Items are
American
Made
Fiberglass
Components. Manufactured
and shipped F.O.B. Hampton Florida 32044
68-69 Stock Hood
Heavy Duty Features:
- 90 edges on both sides help to
maintain fender contours.
- Full perimeter inner frames - utilizes
OEM hinge & latch.
Additional hold downs recommended.
- Black lacquered fiberglass textured
inner finish.
- Sandable gray gellcoated exterior
finish.
- Coremat® reinforced skin aids in
reduction of print-thru.
- Add a new scoop for as little as $50 w / purchase.
68-69 Super
Sport Hood
Heavy Duty Features:
- Styled after the original SS design.
- 90 edges on both sides help to
maintain fender contours.
- Full perimeter inner frames - utilizes
OEM hinge & latch.
Additional hold downs recommended.
- Black lacquered fiberglass textured
inner finish.
- Full Open inner chamber provides no
additional clearance. Original Chrome
trim required.
68-69 Cowl
Induction 2" Hood
Heavy Duty Features:
- Styled after the original Z-28 design.
- 90 edges on both sides help to
maintain fender contours.
- Full perimeter inner frames - utilizes
OEM hinge & latch.
Additional hold downs recommended.
- Black lacquered fiberglass textured
inner finish.
- Full Open inner chamber provides 2"
of additional clearance.
- Coremat® reinforced skin.
-
You
can add a ram air isolator plate during check out. Installed Photos
68-69 6" Dominator
Hood
Race Weight Features:
- Designed w/Dominator style scoop.
- Installed perimeter bracing baffle.
- Black fiberglass textured inner.
- Sandable gray gellcoated exterior.
- Reinforced skin.
- Dominator scoop provides +/- 6"
clearance at rear & +/- 5" clearance
at stock carb location.
- Edges require sanding for desired fit.
- One piece construction.
-
You
can add a ram air isolator plate during check out.
68-69
6.5" Aero Hood
Race Weight Features:
- Designed w/Pro-Stock style scoop
for maximum ram air flow.
- Installed perimeter bracing baffle.
- Black fiberglass textured inner.
- Sandable gray gellcoated exterior.
- Reinforced skin.
- Scoop comes closed. (33"x6.5"x18")
- Edges require sanding for desired fit.
- One piece construction - Yes, it
comes out of the mold this way!
-
You
can add a ram air isolator plate during check out.
68-69 Cowl
Induction 4" Hood
Heavy Duty Features:
- Styled after the original Z-28 design.
- 90 edges on both sides help to
maintain fender contours.
- Full perimeter inner frames - utilizes
OEM hinge & latch.
Additional hold downs recommended.
- Black lacquered fiberglass textured
inner finish.
- Full Open inner chamber provides 4"
of additional clearance.
- Coremat® reinforced skin.
-
You
can add a ram air isolator plate during check out.
70-72 Stock Hood
Heavy Duty Features:
- 90 edges on both sides help to
maintain fender contours.
- Full perimeter inner frames - utilizes
OEM hinge & latch.
Additional hold downs recommended.
- Black lacquered fiberglass textured
inner finish.
- Sandable gray gellcoated exterior
finish.
- Coremat® reinforced skin aids in
reduction of print-thru.
- Add a new scoop for as little as $50 w / purchase.
70-72 Super
Sport Hood
Heavy Duty Features:
- Styled after the original SS design.
- 90 edges on both sides help to
maintain fender contours.
- Full perimeter inner frames - utilizes
OEM hinge & latch.
Additional hold downs recommended.
- Black lacquered fiberglass textured
inner finish.
- Full Open inner chamber provides 1"
of additional clearance.
- Coremat® reinforced skin.
70-72 Cowl
Induction 2" Hood
Heavy Duty Features:
- Styled after the original Z-28 design.
- 90 edges on both sides help to
maintain fender contours.
- Full perimeter inner frames - utilizes
OEM hinge & latch.
Additional hold downs recommended.
- Black lacquered fiberglass textured
inner finish.
- Full Open inner chamber provides 2"
of additional clearance.
- Coremat® reinforced skin.
-
You
can add a ram air isolator plate during check out.
70-72
6" Dominator Hood
Race Weight Features:
- Designed w/Dominator style scoop.
- Installed perimeter bracing baffle.
- Black fiberglass textured inner.
- Sandable gray gellcoated exterior.
- Reinforced skin.
- Dominator scoop provides +/- 6"
clearance at rear & +/- 5" clearance
at stock carb location.
- Edges require sanding for desired fit.
- One piece construction
-
You
can add a ram air isolator plate during check out.
70-72
6.5" Aero Hood
Race Weight Features:
- Designed w/Pro-Stock style scoop
for maximum ram air flow.
- Installed perimeter bracing baffle.
- Black fiberglass textured inner.
- Sandable gray gellcoated exterior.
- Reinforced skin.
- Scoop comes closed. (33"x6.5"x18")
- Edges require sanding for desired fit.
- One piece construction - Yes, it
comes out of the mold this way!
-
You
can add a ram air isolator plate during check out.
70-72
L-88hp 3.50 Hood
Heavy Duty Features:
- Styled after the original L-88 design.
- 90 edges on both sides help to
maintain fender contours.
- Full perimeter inner frames - utilizes
OEM hinge & latch.
Additional hold downs recommended.
- Black lacquered fiberglass textured
inner finish.
- Full Open inner chamber provides 3.50"
of additional clearance.
- Coremat® reinforced skin.
-
You
can add a ram air isolator plate during check out.
- 90 edges on both sides help to
maintain fender contours. Edges come
long & require minor trimming for
correct fit.
- Full inner frames - utilizes OEM hinge
& latch.
- Fully
lined - smooth gellcoated inner
utilizes OEM hinge & latch.
Additional hold downs recommended.
- Sandable gray gellcoated exterior
finish.
- Coremat® reinforced skin reduces
"print thru".
- Scoop and Inner liner come closed.
68-69 Front Fender
70-72 Front Fender
70-72 E.C. Front Fender Race Weight Features:
- Smooth gray gellcoat exterior finish..
- Fiberglass texture, Black lacquer inner finish.
- Hood Jam holes, hinging and attaching points must be opened for installation.
- Mold flashing must be removed for finishing.
- No other reproduction fiberglass fenders come so complete.
- Partial inner jam provides attach points only.
- Not designed for hinge type hood.
- Fiberglass race weight pin-on hood required.
68-69 S.S. One Piece Front End68-69 Pro Front End70-72 S.S. One Piece FrontEnd
Front
End Features:
- Heavy Duty version - does not come with a hinge kit or
installation hardware.
- Grey exterior gellcoat finish can be easily sanded and prepared for finishing.
- Smooth 90° roll into wheel well openings, generally extends in a full
¾".
- Headlight blanks require opening to install light bowl and trim.
- The units do come with mold flashing - which must be fared in before
preparing for paint.
- The interior finish is Fiberglass texture - coated in black lacquer - it comes
without wheel wells.
Wheel wells cannot be completely attached to the front end as they will
interfere with engine &
firewall component, when hinging.
-
Light Weight Version - is
intended for racing applications and does not come with a hinge
kit or
installation hardware..
- These unit generally only weigh in at approx 30# +/- .
- Pro-Package Includes: Pro Front end, Choice of hood, 2
Doors & Choice of trunk. Please e-mail us after placing your order.
Reference your order number and specify your choice of hood and
trunk by part number. Race weight parts only.
Front End
Installation Tips
Easy On
Fish Mouth Design.
A good idea a customer came up with
- was to use fish mouth tubing - a large piece mounted to the frame rail
and a somewhat smaller one glassed to the front end itself. When
sliding the front end on it not only self aligns it secure the front end
and fasteners are only needed in the rear.
Tilting One Piece Front Ends
Most of the work to tilt a full
fendered front end can be accomplished at the drawing table. First you
will need a photo of the side of the vehicle. draw an outline of
its' front end on tracing paper. Cut the outline drawing and lay it
over the photo. With the use of a pin, determine where the hinge
placement should be (The pin acting as the hinging point.) be sure
that your paper model when tilting, does not have the fender hitting the
tire or the grill hitting the ground.
To get more lift
and clearance while
tilting, a double hinge
can be fabricated and used. For either double
or single hinges, you must start by fiberglassing a 1 x 1 steel bar into
the front end, just above and in front of the hinge point.
Make sure, before glassing the bar in that a pad is welded on the end to
make it more stable.
For single hinge mechanism - weld or bolt
an other plate coming off of the frame rail and drill the 1/2" hole in
the same location. With the use of a 1/2" bolt & fiber lock nut ,as
your hinge, the front end should pivot properly. Whatever you do
TAKE YOUR TIME!
For a double hinge mechanism, weld an oval plate
off of the bar in the front end (previously installed) angled down and
behind the hinge point. Cut an oval plate to bolt to the frame
horn and add 2 stop bolts to limit the travel. Doing your best to make your
assembly look
like the animation to the right. It is best to use stainless steel bolts and
cotter pin type lock nuts, for a secure installation...and again
whatever you do TAKE YOUR TIME!
IMPORTANT - Please specify the type of racing that the unit will be used for, so we
may build and reinforce your unit accordingly. Units manufactured for "Street
Racing" have a heavier roving on all edges to reduce the chance of tearing (under to
stress of impact) and usually weigh 10 - 15# more than a Drag Racing unit.
Units manufactured for "Sand Drag" or "Baja" style racing are built so
as to be midway between the Street Drag and the Street Race units.
69-72
Trunk Lid
Heavy Duty Features:
- 90 edges on both sides help to
maintain fender contours.
- Full perimeter inner frames - utilizes
OEM hinge & latch.
- Black lacquered fiberglass textured
inner finish.
- Sandable gray gellcoated exterior
finish.
- Coremat® reinforced skin aids in
reduction of print-thru.
70-72 Race Body Shell
Please Note: We are unable to
ship body shells. They must be picked up in person to avoid freight
damage.
When building a race vehicle you
obviously want it as
lightas possible. So you cut out the floor pan -wheel
wells & inner structure.....As far as the body all you are left with is an
overweight, floppy shell held together with old factory spot welds and body lead. Our bodies are manufactured from extremely complex molds - which produce a rigid
one piece unit. The roof, quarters & firewall are generally stiffened with the
use of internal ribbing. In addition, your all new glass body can be made heavier or
lighter (within reason) depending on your application. Average body weight is
only about 100#'s.
As far as body
work, you need to scuff off the mold flashing - block sand - prime and paint. The
great part
about owning a rigid glass body - is that you'll never have to worry about
rust. Once you apply your paint scheme that's it - just wash and wax.
Installation
is a snap! Whether you are
installing just the body or an entire package, the bodies attach at the rocker panels,
tail pan, trunk jam, door jam, and front and rear window jams. We also offer
fiberglass wheel tubs, which can be glassed
directly to your new body. (This is done by the installer).
68-72 Doors
(68-69
left - 70-72 right)
Race Weight Features:
- Smooth interior panel. (As Shown Above)
- Will accept original handle, hinge & latching
mechanism.
- All holes come closed & must be opened for
installation.
- Available in Light Weight
design only.
- Strictly intended for Racing application only!
- Fully gellcoated inner & outer surface.
- Plastic windows required attached to
inner
door frame.
