(U.S. Body Source is not affiliated with GM, Ford, Chrysler or any other vehicle manufacturer).
The use of name s and headings is for the sole purpose of identification.
 

 

 

 

 

 

 

               

This site has moved...    Enter here.

 

 

 

 

 

 

Click Here to Bookmark this Site !

73-87 Chevy Truck   Part Pictures
All Items are American Made Fiberglass Components  

                                                    
Reinforced Door Jams Complete with Air Box Smooth Gellcoat Finish

                                             (Click for Cab Installation)
73-87 Cabs
  Short Wheel Base 117.5"  -  Long Wheel Base 131.5" - Blazer W.B. 106.5"
Features:
 - One Piece Outer shell construction - with a few well hidden mold seams.
 - Smooth, easy to prep and paint, gray sandable exterior gellcoat finish.
 - Aluminum plate reinforced firewall & door hinge areas provides the necessary strength for 
   proper support of factory doors & hardware.
 - Marine Grade Pressure treated floor support beams are sealed into the fiberglass and covered 
   with black lacquer finish. 
 - The unit arrives bare without dash, doors or any mechanical or electrical devices.
 - Headliner is supplied and comes with a smooth paintable gellcoat interior finish. 
   (Comes  separately  and requires professional installation.) 
 - Light Weight Model comes with out floor and firewall - This unit is solely intended for serious 
   racing applications.  Tube chassis and metal interior work is required. (Approx. weight 50 -
   70#)
  

 

Heavily reinforced floor

Aluminum reinforced door hinge area.

                                                             (Click for Brief Blazer Installation)
Note:                                                                                               
 
Cabs - although strong, straight, rust free & reliable - are not the project for the average "Joe".  They are intended for the serious "Ground Up Builder" who has the time, money & experience to do the job correctly.  

All safety concerns must be taken up with the chassis shop involved with the project.  

  Once finished these cabs look exceptional and should just about last forever, however, sit down and Please give some serious thought before ordering........We prefer that our customers be confident & educated in the amount of work required to complete this project and secure in the choice that you make.

                                                      

Reinforced tailgate area.

Windshiel opening - Oversized

Fully Ribbed rear floor

76-91 Chevrolet Blazer Tubs. . . . . . . . . Heavy Duty . . . . .Rust Free . . . . . Box Section Side walls. . . . . Full Firewall Air Box w/floor vent area . . . . . .

Full convertible

Rust Free Quarters!

For Convertible Cabs or build a "stubby " Blazer Pick up

73-75  Blazer Tubs. . . . . . . . .Full convertible . . . . . . . Heavy Duty . . . . .Rust Free . . . . . Box Section Side walls. . . . . Full Firewall Air Box w/floor vent area . . . . . .
    
All parts shown above were used on our 73-80 Chevy Build-Up                  (Click for Chevy Build-Up)
73-80 Stock Hood

73-80 Stock Hood
    
H/D Features:
 - Smooth grey gellcoat finish.
 - Frame uses existing Hinge &
   Latch.
 - Fiberglass texture inner coated
   with Black Lacquer.
 - Smooth Grey gellcoat outer
   finish.
   
   ( Link to H / D Hood Construction)
73-80 Stepdown Hood

73-80 Stepdown Hood
H/D
Features:
 - Smooth grey gellcoat finish.
 - Frame uses existing Hinge
   only (Discard Latch)
 - Fiberglass texture inner coated
   with Black Lacquer.
 - Smooth Grey gellcoat outer
   finish.
   
( Link to H / D Hood Construction)

73-80 Cowl Induction  Hood

H/D Features:
 - Styled after the Z-28 design.
 - 90 edges on both sides help to
    maintain fender contours.
 - Fully Lined TECHHOOD™ design
 - Utilizes OEM hinge & latch.
 - Smooth Gellcoated. paintable inner
   finish. Scoop & baffle come closed.
 - Full Open inner chamber provides 2."
   of additional clearance.
 - Coremat® reinforced skin.
       H/D Const.     L/W Con
Air Box needs to be opened for clearance.
Smooth gelcoat finish !
73-80 Super Sport Hood 
H/D Features:
 - Styled after the 2000 Z-28 design.
 - 90 edges on both sides help to
    maintain fender contours.
 - Fully Lined TECHHOOD™ design
 - Utilizes OEM hinge & latch.
 - Smooth Gellcoated. paintable inner
   finish. Scoop & baffle come closed.
 - Full Open inner chamber provides 3."
   of additional clearance.
 - Coremat® reinforced skin.
     H/D Const.     L/W Const
Scoop & Baffles come closed
73-80 Cowl Induction  Hood 
H/D Features:
 - Styled after the original Z-28 design.
 - 90 edges on both sides help to
    maintain fender contours.
 - Fully Lined TECHHOOD™ design
 - Utilizes OEM hinge & latch.
 - Smooth Gellcoated. paintable inner
   finish. Scoop & baffle come closed.
 - Full Open inner chamber provides3.5"
   of additional clearance.
 - Coremat® reinforced skin.
      H/D Const.     L/W Const
Coremat® reinforced skin.
                                                       
81-87 Stock hood

81-87 Stock Hood
H/D Features:
 - Smooth grey gellcoat finish.
 - Frame uses existing Hinge &
   Latch.
 - Fiberglass texture inner coated
   with Black Lacquer.
 - Smooth Grey gellcoat outer
   finish.
   

   ( Link to H / D Hood Construction)

81-87 Stepdown Hood

81-87 Stepdown Hood 
H/D Features:
 - Smooth grey gellcoat finish.
 - Frame uses existing Hinge
   only (Discard Latch)
 - Fiberglass texture inner coated
   with Black Lacquer.
 - Smooth Grey gellcoat outer
   finish.


   
( Link to H / D Hood Construction)

81-87 Indy 2" Cowl Induction Hood

81-87 Indy Cowl Hood 2"
H/D Features:
 - Indy design provides 2" extra
   clearance - Air box comes
   closed.
 - Fully Lined TECHHOOD™
   design Bolts Directly to the
    OEM hinge & Latch.

 
- Smooth Grey gellcoat outer
   finish.
   

 
Hood Construction        Scoop Opening

81-87 4" Cowl Induction Hood
81-87 Cowl Induction  Hood 

H/D Features:
 - Styled after the original Z-28 design.
 - 90 edges on both sides help to
    maintain fender contours.
 - Fully Lined TECHHOOD™ design
 - Utilizes OEM hinge & latch.
 - Smooth Gellcoated. paintable inner
   finish. Scoop & baffle come closed.
 - Full Open inner chamber provides3.5"
   of additional clearance.
 - Coremat® reinforced skin.
       H/D Const.     L/W Const

Fully Lined TECHHOOD™ design

81-87 Super Sport Hood
81-87 Super Sport Hood 

H/D Features:
 - Styled after the 2000 Z-28 design.
 - 90 edges on both sides help to
    maintain fender contours.
 - Fully Lined TECHHOOD™ design
 - Utilizes OEM hinge & latch.
 - Smooth Gellcoated. paintable inner
   finish. Scoop & baffle come closed.
 - Full Open inner chamber provides 2."
   of additional clearance.
 - Coremat® reinforced skin.
     H/D Const.     L/W Const

Fully Lined TECHHOOD™ design

81-87 Ram Air II Hood
81-87 Ram Air II Hood 

H/D Features:
 - Styled after the 2000 T/A design.
 - 90 edges on both sides help to
    maintain fender contours.
 - Fully Lined TECHHOOD™ design
 - Utilizes OEM hinge & latch.
 - Smooth Gellcoated. paintable inner
   finish. Scoop & baffle come closed.
 - Full Open inner chamber provides3."
   of additional clearance.
 - Coremat® reinforced skin.
      H/D Const.     L/W Const
Scoops & Baffles come closed
                                                      

73-80 Front End

73-80 Pre-Split Cowl Tilt

81-87 Front End

        73-80 Front End         73-80 Pre-Split Cowl Tilt            81-87 Front End
73-87 Front Ends    (All Units are Interchangeable between the years - Chevy or GMC)                                                                                                                   (Click for Tilt Installation)
 
Features:
 -
Heavy Duty version - comes complete with hinge kit - click above for all the "How To" information
 - Grey exterior gellcoat finish can be easily sanded and prepared for finishing
 - Smooth 90° roll into wheel well openings, generally extends in a full  ¾".
 - Marker blanks require opening to install. 
 - The units do come with mold flashing - which must be fared in before preparing for paint. 
 -
Pre-Split Front End models come with the lower fender section (the part between the door and tire)
   separate.
   It is manufactured with a tongue & groove joint on both the panel and the front end, to help in
   closing alignment.
 -
One Piece Front Ends do need the rear fender panel to be cut in order to utilize the hinge kit
   supplied.....They can be made to slide forward than tilt without cutting the fender, however, this
   depends on the tire size and will involve detailed planning and fabrication on the installers part.
 - The interior finish is Fiberglass texture - coated in black lacquer - it comes without wheel wells.
    Wheel wells cannot be completely attached to the front end as they will interfere with engine &
    firewall component, when hinging.
81-87 Pre-Split Cowl Tilt

     81-87 Pre-Split Cowl Tilt        (Click for Tilt Installation)
 - Light Weight Version - is intended for racing applications and does not come with a hinge kit.    
 - These unit generally only weigh in at approx 30#  +/- .  
 - Pre-Split models are not available in Light Weight.

NOTE:  When ordering Light Weight version truck racing components are "Special Order" and 
            Non Returnable. 

IMPORTANT - Please specify the type of racing that the unit will be used for, so we may build and reinforce your unit accordingly. Units manufactured for "Mud Bog" racing have a heavier roving on all edges to reduce the chance of tearing (under to stress of impact and mud load) and usually weigh 
10 - 15# more than a Drag Racing unit.  Units manufactured for "Sand Drag" or "Baja" style racing are built so as to be midway between the Street Drag and the Mud Bog units.
                                                       

81-87 Wheel Well

73-87 Wheel Well
Features:
 - Smooth grey gellcoat finish.
 - One Piece fiberglass
   construction. 
 - Battery Acid resistant
   Gellcoat.
 - All Holes are closed and
   require drilling for installation.

Blazer Floor Pans

73-91 Blazer Frt. Flr. Pan
Features:
 - Smooth grey gellcoat finish.
 - One Piece fiberglass
   construction. 
 - Rivets in place.
 - Designed to cover floor board
   rot.

Smooth Gellcoat Finish

73-80 Dash repro
Features:
 - Smooth grey gellcoat finish
 - One Piece fiberglass
   construction 
73-87 Front Bumper
 
- All Holes are closed and
   require drilling for installation.
73-87 Door

Detailed Inner

Uses original latch
73-87 Door - Hinge Type
H/D Features:
 - Smooth grey gellcoat finish both inside and out.
 - Accepts original hinge, latch & regulator hardware
 - Double wall posts support upper window and track.
 - Windows come blanked in and must be opened during installation
 - Coremat® reinforced outer skin reduces "print thru".
 - Original felts can be epoxied in the door post and side track.
 - Door is supplied bare with no glass, mechanism, tracks or hardware.
                                                                                                         
(Click for Additional Door Info)
Bedside Skin
Stepside Fender w/ Step
73-87 Fleetside Bedside
 
Features:
 - Smooth grey gellcoat exterior finish - Fiberglass textured Black
   Lacquer inner.
 - Skin Only - Will not bolt to stock location.
73-87 Stepside Fender w/step
 
Features:
 - Smooth gray gellcoat exterior
   finish - Fiberglass textured
   Black Lacquer inner.
 - Smooth 90° roll into wheel well
 - Rear flange holes come closed
   and require back drilling for
   correct alignment.
Complete with Fenders & Steps Recessed Floor Box only

73-87
Stepside Bed
(Short Wheel Base Box - 117.5" w.b.) 
H/D Features:
 - Bed Comes complete with fenders & steps attached - as one piece.  Ideal for customized or
   frenched in taillight applications.
 - Double panel side walls, with a smooth gray gellcoat inner and outer finish.
 - Hollow sealed stake pocket - can be opened if desired for original appearance.
 - Design for use and abuse with heavy Marine Grade PT under floor reinforcements - which can
   support the same weight load as the original bed.
 - Gellcoated Fiberglass floors - recessed 3/4" to allow for the installation of "Aftermarket" Bed Wood
   Kits.
 - Black lacquer over fiberglass texture underneath the bed floor and on the forward side of the back
   splash.
                                                       
Standard Box Tubbed Box
 - Tubbed bed allows for 21" clearance from tub to wheel opening flange.  This allows for 20"-21"
    tires.
   The distance between the tubs is 33".
 - Side flange is angled and does not have the curled design of the original bed (Due to compound
   curve & fiberglass mold limitations.)
 - Installation time (after removal of original box ) 1-2 hours.
 
NOTE: 
  To install - simply drill thru the bed and the under floor reinforcements and thru bolt it in place with O.D washers.  It may be necessary to drill a new mounting hole through the existing frame.  Drilling - sanding and possible notching of under floor braces may be required for correct installation of your NEW and
IMPROVED, RUST FREE, DENT FREE  bed assembly.  (Ground wire required for electrical).
Reinforced Tailgate opening - 6 Foot Fleetside It will NEVER rust ! Double Panel Boxed Sides

73-87
Fleetside Bed
(Long Wheel Base Box - 131.5"  - Short Wheel Base )  
H/D Features:
 - Bed Comes complete with bedsides attached - as one piece.  Ideal for customized or
   frenched in taillight applications.
 - Box section side walls, with a smooth grey gellcoat inner and outer finish.
 - Hollow sealed stake pocket - can be opened if desired for original appearance.
 - Design for use and abuse with heavy Marine Grade PT under floor reinforcements - which can
   support the same weight load as the original bed.
 - Gellcoated Fiberglass floors have a ribbed design - eliminated the need for a Wood kit.
 - Black lacquer over fiberglass texture underneath the bed floor and on the forward side of the back
   splash.
 
   
                                                    
Fully Ribbed Floor Fully Reinforced Floor
 - Installation time (after removal of original box ) 1-2 hours.
 
NOTE: 
  To install - simply drill thru the bed and the under floor reinforcements and thru bolt it in place with O.D washers.  It may be necessary to drill a new mounting hole through the existing frame.  Drilling - sanding and possible notching of under floor braces may be required for correct installation of your NEW and
IMPROVED, RUST FREE, DENT FREE  bed assembly.  (Ground wire required for electrical).


Push to Reveal Order Form

Home | Order Now | E-Mail
 Rebate | About us | Catalog | Games
 Part Construction | Installation | T-Shirts | Photos


usbody.com 
Quality Automotive Body Panels Since 1987
8823 Van Fleet Road Riverview Florida 33578
Secure on-line ordering available 24/7 
FAX Orders can be placed anytime at (352) 468-2164 
For more information or to check on an existing order e-mail us at customerservice
@usbody.com  
This site is updated daily. All components manufactured are listed 
on this site. (If you don't see your parts listed, they are not available.) 

© Copyright 1987-date 
® U.S.Body Source inc., usbody.com, carhoods.com, gr8hoods.com, techhoods.com, e-bodyparts.com
The text and images in the afore mentioned sites may not be reproduced for commercial purposes without 
express written permission from U.S.Body Source inc.
8823 Van Fleet Road Riverview Florida 33578